FAQ

SCREEN PRINT

How long do I expose my emulsion?

All emulsions are different, so we recommend using an exposure calculator, or a step wedge to determine the correct time.

Why does the plastisol print crack on the garment after the first wash?

The plastisol was not cured properly if the ink is cracking. It could have been the temperature on the dryer being too low, or the time allowed to dry was not long enough.

How many shirts can I print with one quart of ink?

Depending on how big the design is, anywhere from 500-800 shirts.

Will my t-shirts look like professionally screened shirts as seen in a store?

All printing supplies listed are professional supplies. You have all the opportunity to make a professional product, however, it takes practice.

Why does the white ink turn pink when I print on red? Why does the white ink turn grey when I print on black?

In most cases the white ink being used is not a low bleed white. A low bleed white ink will block the dye migration that causes this problem.

Why am I left with a ghost image after reclaiming a screen print frame?

Most ghost images are a stain on the polyester and can be removed with a haze remover.

Still have questions? Contact our knowledgeable team today.

1 SHOT

What should I use for reducing 1 Shot Lettering Enamel?

To enhance flow characteristics, you can reduce with 1 Shot Reducer, also available in low and high temp versions. Never use Mineral Spirits.

Why am I getting "Fish Eyes" or "Crawling" when using 1 Shot Paints?

If a surface is not thoroughly cleaned, it may still contain waxes, oils or silicons. Clean with a good surface prep and degreaser.

Can I reduce or eliminate the gloss of my 1 Shot Lettering Enamels?

Yes. Our 1 Shot / Chromatic #4329500 Flattening Paste can be used in varying ratios to reduce gloss, or even create a dead flat finish.

Can I clear coat over 1 Shot Lettering Enamels?

Yes. It is important that your paint is completely dry prior to overcoating. We recommend that you use our 1 Shot #4007 Hardener and wait at least 24 hours prior to clearing. Adding up to 20% Hardener, with no other reducers, will allow for overcoating with automotive type urethane clears after 24 hours. Always apply the first two coats of clear very light and dry when clear coating.

What should I know about painting 1 Shot Lettering Enamels through a mask?

When applying paint through a computer-generated or hand cut mask, always remove the masking material once the paint "tacks" (usually about 15-20 minutes), but before it dries.

Why won't my 1 Shot Lettering Enamels dry on a banner?

To letter on a banner (or any vinyl-based, flexible surface such as awnings, tonnau covers, leather garments), the banner must have an "Enamel Receptive Coating" on it. If you don't have an "ERC" banner, you can coat the banner first with our Ti-Cote product to make it enamel receptive.

What procedure should I follow to prepare MDO for 1 Shot or Chromatic Enamels?

Clean the surface thoroughly, then scuff lightly with an abrasive pad. On unprimed MDO, prime with Chromatic Primer. On pre-primed MDO, after using a tack rag to remove any residual sanding dust, roller on your Lettering or Background Enamel. Apply in two or three light coats, as opposed to one heavy coat. If you get little bubbles in the surface, (usually from using a foam roller) immediately re-roller, but slightly "lift" on the roller frame, taking virtually all the pressure off the roller.

How do I avoid wrinkling in my Lettering or Background Enamels?

Never try to recoat a painted surface until the first coat of paint is dry. Always follow the suggested recoating times for best results.

What if I need a color not offered by 1 Shot?

1 Shot Lettering Enamels are infinitely mixable. By combining from our 44 color selection, and/or our special Tinting White, Tinting Black, and Super Gloss Tinting Clear, you can create ANY color, in various configurations ranging from opaque to glistening, transparent candy colors.

How do I mix a PMS color match using 1 Shot Paints?

PMS formulations, used primarily in the offset and screen printing fields are created by mixing three transparent colors (cyan, magenta and yellow), as well as black.

Is it acceptable to store my 1 Shot Lettering Enamels in squeeze bottles?

While it is acceptable, there are a couple of important points to remember: Normal "plastic" (PVF, PVC, etc.) squeeze bottles, as found at beauty supply centers and even through some sign supply sources, can allow for plasticizer migration from the bottle to the paint; resulting in slower drying times, lower gloss levels and ultimately reduced exterior durability.
Make sure the bottles you store your 1 Shot in are made of PET (Polyethylene terephthalate ); and it is advisable, when practical, to store these bottles upside-down to help prevent skinning over of your paint. When storing 1 Shot Metallics or Pearlescents in PET bottles, drop a ball bearing into the bottle to aid in thorough mixing when shaking your bottles.

Still have questions? Contact our knowledgeable team today.

Mclogan’s Current Special

WYSIWYG goes here (already dynamically implemented)...